We are here for your questions anytime 24/7, welcome your consultation.
Get Price
Dec 19, 2019 This percentage is known as a crushing value of aggregate. This percentage should not exceed 30% of the total weight of aggregate taken for the test. The aggregate crushing value test result should not be more than 30 % for the concrete used for roads and pavements and, in case of other structures; it may be permitted up to 45%.
The behaviour and properties of concrete and concrete making materials can be better understood by conducting first-hand experiments in the laboratory. Thus, the objective of this manual is to make the students aware of different tests required to be performed for these materials as per Indian standards and the acceptable limiting values.
aggregates, aggregate abrasion value and soundness test for aggregates have been revised, Recommendations have been included for the size of ... 0.6 Indian Standards Methods of test for aggregates for concrete [IS:2386 (Part I)-1963 to IS: 2386 (Part VIII)-19631 are necessary ... line aggregate produced by crushing natural gravel. .
Aggregate crushing value test (IS:2386-1963) (1) (2) Apparatus and materials Procedure : 4-9: ... Rr310101 Concrete Technology and Prestressed Concrete
viva questions on aggregate crushing value test - BINQ …
Jul 21, 2020 With technological advancement on the rise, manual crushing of bricks is gradually being replaced by machine crushing to obtain coarse aggregates for construction. However, properties of the brick aggregates obtained from these two methods vary which in turn, may affect the properties of the concrete matrix as well. This study represents a comparison between the machine crushed and …
By this single test one judge that whether Concreting has been done properly or not. Concrete compressive strength for general construction varies from 15 MPa (2200 psi) to 30 MPa (4400 psi) and higher in commercial and industrial structures. Compressive strength of concrete depends on many factors such as water-cement ratio, cement strength ...
Procedure. Step 1 – First, the aggregate sample sieve through 12.5mm sieve and collect it which is retained in 10 mm sieve. Step 2 – Now, the sample should be dried through the oven up to 4 hours at 100 deg to 110 deg. Step 3 – Then, the aggregate sample should be filled in the metal cup by 3 layers. Each layer should be tamped 25 times by the tamping rod.
Oct 01, 2017 Aggregate Impact Value: BSI BS 812-112 (1990c) Aggregate Crushing Value: AS 1141.21 (1997) BSI BS 812-110 (1990b) Micro-Deval Abrasion: AASHTO TP 58 (1999) ASTM D6928 (2010) AENOR UNE-EN 1097-1 (2011) Texas Ball Mill (Wet) AS1141.28 (2014) Country Roads Board, Victoria – Test Method 341 (National Association of Australian State Road ...
37. Aggregate crushing value of material A is 40 and that of B is 25. Which one is better and why? 38. How is aggregate impact value expressed? 39. Aggregate impact value material A is 20 and that of B is 45. Which one is better for surface course? Why? 40. Explain ductility of Bitumen and its significance? Concrete Technology LAB VIVA ...
300+ REAL TIME Concrete Technology LAB VIVA Questions
Sep 12, 2015 Fig-3 Impact Test Setup. The aggregate impact test is carried out to evaluate the resistance to impact of aggregates. Aggregates passing 12.5 mm sieve and retained on 10 mm sieve is filled in a cylindrical steel cup of internal dia 10.2 mm and depth 5 cm which is attached to a metal base of impact testing machine.
CHAPTER 3—AGGREGATE PROPERTIES AND TEST METHODS 3.1—Grading 3.1.1 Definition and test method—Grading refers to the distribution of particle sizes present in an aggregate. The grading is determined in accordance with ASTM C 136, “Sieve or Screen Analysis of Fine and Coarse Aggregates.” A sample of the aggregate is shaken through a ...
Jul 01, 2021 The application of CO 2 Concrete in this environment is a test for the replacement of conventional, virgin aggregate concrete and offers an excellent practical examination of the sustainable CO 2 Concrete. In order to accommodate the requirements of functionality of the slabs, they must be 3 m in length, 2.6 m in width and 0.2 m in thickness.
Design of Concrete Structures MCQ Practice Test – Set 11. ... Log Angles machine is used to test the aggregate for (A) Crushing strength (B) Impact value (C) Abrasion resistance (D) Water absorption. ... Categories Concrete Technology and Design. Leave a …
Dec 19, 2019 This percentage is known as a crushing value of aggregate. This percentage should not exceed 30% of the total weight of aggregate taken for the test. The aggregate crushing value test result should not be more than 30 % for the concrete used for roads and pavements and, in case of other structures; it may be permitted up to 45%.
7 Lab Test on Aggregate Should Satisfy for Use in Concrete
The aggregate crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement aggregate possessing low aggregate crushing value should be preferred. The aggregate crushing value of the coarse aggregates used for cement concrete pavement at
Aggregate impact and crushing test - Slideshare. Feb 8, 2012 ... Aggregates ppt LATIF HYDER WADHO 7,234 views .... 105 per cent of the Aggregate Crushing Value and itcan be used for the same purpose. ... Apparatus for the 10% fines test and aggregate crushing test (Millard, 1993) 2. Read more
Cracks may form when more fineness aggregates are used in concrete. A high fineness value indicated the aggregate is coarser and a low fineness value indicates the aggregate is finer. The sieve analysis test founds the fineness of the aggregate. 10. Surface area of aggregate. The surface area of fine aggregate is higher than the coarse aggregate.
Oct 01, 2016 The aggregate crushing strength value is a useful factor to know the behavior of aggregates when subjected to compressive loads. Also read: Crushing Value Test of Aggregates. 13. Impact Value. The aggregate impact value gives a relative measure of the resistance of an aggregate to sudden shock or impact.
280. In the context of air entrainment in fresh concrete consider the following statements: Statement-1: Air entrainment is required in cases when concrete is likely to be subjected to alkali aggregate reaction. Statement-2: Air entrainment has the effect of increasing the workability of concrete …
Concrete Technology MCQ - Aggregate MCQ | Page 27 of …
Steel ball bearings in the hardness test To produce the abrasive action using standard steel balls that, when mixed with the aggregate and rotated in a drum for a specific number of revolutions, impact the aggregate.. The wear per age due to friction with steel balls is determined and is known as the abrasion value.
abundantly available from crusher units at a low-priced in many areas, maintain practical option for concrete river sand. Table-3.3 Physical Properties of Fine Aggregate S.NO PROPERTIES TEST VALUES RS MS QS 1 Specific gravity 2.6 2.8 1.8 Fineness modulus 2.25 2.4 2.56 3 Buckling 23.7% 25.24% - 4 Water absorption 2% 4% 0.6% 3.4.
The behaviour and properties of concrete and concrete making materials can be better understood by conducting first-hand experiments in the laboratory. Thus, the objective of this manual is to make the students aware of different tests required to be performed for these materials as per Indian standards and the acceptable limiting values.
Digital Los Angles Abrasion Testing Machine: The machine consists of an electronic control unit and a rolled steel drum having an inside diameter of 711 mm and internal length of 508 mm. The drum is rotated at a speed of 31-33 r.p.m. The internal shelf provided with the machine confirms to ASTM, AASHTO and EN standards.
Aggregate impact test value ... 2.4 Aggregate Crushing Test . ... Shetty MS 1963 Concrete Technology Theory and Practice 2008, S.Chand & company Ltd. Advertisement.
Effectiveness of Using Recycled Coarse Aggregate in Concrete
Keywords: Sawdust, Concrete, Workability, Aggregate Crushing value, Compressive strength, 1. Introduction The overall relevance of concrete in virtually all civil engineering practice and building construction works cannot be overemphasized (Adewuyi and Adegoke, 2008). Concrete is a combination of cement, fine and coarse
If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!
Kexue Revenue, High and New Technology Industrial Development Zone, Zhengzhou, China
Get Latest Price
The environmental protection mobile crushing station can be roughly divided into two types: tire type station and crawler type. The tire type crusher is mainly used for crushing small and medium-sized ore quarry, while the crawler type mobile crusher is mostly used for gravel operation in mountainous areas with worse conditions. In addition, the mobile crusher is low-carbon and environmentally friendly, and the price is relatively affordable. Welcome to consult and buy.
Vertical shaft impact crusher is also called sand maker which is highly efficient stone crushing equipment with domestic and international leading level researched and manufactured by Hongxing Machinery based on introducing the famous “stone impacting stone” crusher principle
Raymond mill, also known as Raymond mill, adopts the advanced structure of similar products at home and abroad, and is updated and improved on the basis of Raymond Mill in the same industry. This equipment has higher efficiency, lower power consumption, smaller floor area and less one-time investment than ball mill.
